DRONE Racer FuriBee Stormer 220... IMPRESSÕES e VOO em FPV
Link do Drone:
Minhas impressões sobre o FuriBee Stormer 220, um ótimo drone que dará uma bela briga com o Wizard X220s
--------------------------------------------------------------------------------------
Apoie o Canal:
Facebook:
Instagram:
Twitter:
Especificações do Drone
Specifications:
- Material: 3K carbon fiber frame
- Arm thickness: 4mm
- Wheelbase: 220mm
- Frame weight: 95g
Omnibus F4 PLUS Flight Controller:
- MCU: STM32F405RGT6
- Motion processing unit: MPU6000
- Integrated OSD chip: AT7456E
- Video transmitter: 5.8G 48CH 25MW / 100MW / 200MW
- Image transmission: IPEX-2 antenna connector
- Receiver port: DSMX, IBUS, PPM, SBUS
- LED_Strip port: yes
- LED buzzer module: yes
- Voide INPUT port: switchable from 5V to battery voltage; default input: 5V
- Supported micro SD card: included
- UART3 ports: TX3, RX3
- LC filter
- Built-in 5V 3A BEC
Electric Speed Controller:
- 4 IN 1 BLHELI-S 35A 3-6S
- Communication protocol: Dshot, Oneshot, Multishot, PWM
- Firmware: BLHELI_S J_H_15_REV16_6
Brushless motor:
- Mode: FuriBee 2308
- KV: 2200KV
- Input voltage: 3-6S
- Maximum pulling force: 1865g
Camera:
- FuriBee HS1177 2.5mm 600TVL
- Lens: 2.5mm
- Wide camera: 130 degrees
- Sensor: CCD 1/3 inches Sony SUPER HAD II CCD
- Resolution:650 tvl ( b / w ), 600tvl ( color )
- Minimum illumination: 0.01Lux
- Operating voltage: 5V-22V
- Operating current: 70mA
- Dimension: 25 x 25mm
- OSD menu: support
- Pixel: PAL: 976 ( H ) x 494 ( V ); NTSC: 768 ( H ) X 494 ( V )
- DNR: 2DNR
- WDR: D-WDR
- Power: DC5V - 22V
- Workplace temperature: -10 degrees to 50 degrees
- Working humidity: 20 to 80 percent
Antenna:
- Frequency: 5.8G
- Impedance: 50 ohm
- Gain: 5dBi
- Maximum power: 50W
- Connector: RP-SMA male
- VSWR: less than 1.5:1
- Polarization: RHCP
- Radiation: omnidirectional
Propeller:
- 5042 three-blade
LED Buzzer Module
- Operating voltage: 5V
Receiver
- PNP: no
- BNF: Frsky XM Plus Receiver
- 1.5km long-distance reception with dual antennas
- 16 channels available. Compatible with D16 mode transmitters
- Operating voltage: 3.7 - 10V
- Operating current: 30mA at 5V
Minhas impressões sobre o FuriBee Stormer 220, um ótimo drone que dará uma bela briga com o Wizard X220s
--------------------------------------------------------------------------------------
Apoie o Canal:
Facebook:
Instagram:
Twitter:
Especificações do Drone
Specifications:
- Material: 3K carbon fiber frame
- Arm thickness: 4mm
- Wheelbase: 220mm
- Frame weight: 95g
Omnibus F4 PLUS Flight Controller:
- MCU: STM32F405RGT6
- Motion processing unit: MPU6000
- Integrated OSD chip: AT7456E
- Video transmitter: 5.8G 48CH 25MW / 100MW / 200MW
- Image transmission: IPEX-2 antenna connector
- Receiver port: DSMX, IBUS, PPM, SBUS
- LED_Strip port: yes
- LED buzzer module: yes
- Voide INPUT port: switchable from 5V to battery voltage; default input: 5V
- Supported micro SD card: included
- UART3 ports: TX3, RX3
- LC filter
- Built-in 5V 3A BEC
Electric Speed Controller:
- 4 IN 1 BLHELI-S 35A 3-6S
- Communication protocol: Dshot, Oneshot, Multishot, PWM
- Firmware: BLHELI_S J_H_15_REV16_6
Brushless motor:
- Mode: FuriBee 2308
- KV: 2200KV
- Input voltage: 3-6S
- Maximum pulling force: 1865g
Camera:
- FuriBee HS1177 2.5mm 600TVL
- Lens: 2.5mm
- Wide camera: 130 degrees
- Sensor: CCD 1/3 inches Sony SUPER HAD II CCD
- Resolution:650 tvl ( b / w ), 600tvl ( color )
- Minimum illumination: 0.01Lux
- Operating voltage: 5V-22V
- Operating current: 70mA
- Dimension: 25 x 25mm
- OSD menu: support
- Pixel: PAL: 976 ( H ) x 494 ( V ); NTSC: 768 ( H ) X 494 ( V )
- DNR: 2DNR
- WDR: D-WDR
- Power: DC5V - 22V
- Workplace temperature: -10 degrees to 50 degrees
- Working humidity: 20 to 80 percent
Antenna:
- Frequency: 5.8G
- Impedance: 50 ohm
- Gain: 5dBi
- Maximum power: 50W
- Connector: RP-SMA male
- VSWR: less than 1.5:1
- Polarization: RHCP
- Radiation: omnidirectional
Propeller:
- 5042 three-blade
LED Buzzer Module
- Operating voltage: 5V
Receiver
- PNP: no
- BNF: Frsky XM Plus Receiver
- 1.5km long-distance reception with dual antennas
- 16 channels available. Compatible with D16 mode transmitters
- Operating voltage: 3.7 - 10V
- Operating current: 30mA at 5V
Rcreviews.lt is not the owner of this text/video/image/photo content, the real source of content is Youtube.com and user declared in this page publication as Youtube.com user,
if you have any question about video removal, what was shared by open community, please contact Youtube.com directly or report bad/not working video links directly to video owner on Youtube.com. Removed video from Youtube.com will also be removed from here.
Advertising